Support
Looper's Delight
|
Support |
|
|
Oh man, I may have to do the same. I just started up the EDP and it went through it's boot process, got to a screen that said, "198 1l" and then did the whole thing over again. It's been OK since though. Mark Sottilaro On Monday, July 22, 2002, at 09:33 PM, Brother Sean wrote: > VICTORY! > Ok so I opened my EDP back up and reseated everything (the first time I > just > reseated the E-Proms) and she's as good as new. > > Thanks fellows, this community is truly amazing in many ways! > > kevin > ---- > www.brothersean.com > > ----- Original Message ----- > From: "Brother Sean" <info@brothersean.com> > To: <Loopers-Delight@loopers-delight.com> > Sent: Monday, July 22, 2002 8:21 PM > Subject: Re: EDP Problem > > >> I disconnected the EDP from midi, powered up and so far this is what >> has >> happened: >> >> (Loop 4 zips by three times and then the version # 1.1 shows) x 16 and >> counting. I think my EDP is getting sicker... >> >> kevin >> >> ----- Original Message ----- >> From: "Brother Sean" <info@brothersean.com> >> To: <Loopers-Delight@loopers-delight.com> >> Sent: Monday, July 22, 2002 8:06 PM >> Subject: Re: EDP Problem >> >> >>> I tried that, I isolated it from midi but it still did the same thing. >> That >>> made me really worried... >>> >>> thanks for your help Kim! >>> kevin >>> ----- Original Message ----- >>> From: "Kim Flint" <kflint@loopers-delight.com> >>> To: <Loopers-Delight@loopers-delight.com> >>> Sent: Monday, July 22, 2002 5:14 PM >>> Subject: Re: EDP Problem >>> >>> >>>> Does it work if you disconnect it from MIDI? Sounds to me like you > might >>>> have a midi loop somehow. >>>> >>>> At 06:00 PM 7/22/2002, Brother Sean wrote: >>>>> I have an EDP with Loop IV. I installed the software about a month > ago >>> and >>>>> everything was working fine but just over the weekend I have had >>>>> some >>>>> troubles. When I intially power up the EDP will cycle through its > LOOP >> 4 >>>>> screen two to three times before allowing me to enter the actually >>> looping >>>>> screen (for lack of a better term the screen where your loop time >>> appears). >>>> >>>> we usually call that "reset" when you haven't recorded any loop yet. > Or >> we >>>> call it the "play state" or "play mode." >>>> >>>>> It used to never take that long just one cycle through. >>>> >>>> I'm not sure if I understood exactly what you are seeing, but >>>> normally >> the >>>> "Loop 4" zips by on the display 3 times at boot up, then stops and > steps >>>> off the display, then shows the version, and goes to the reset state. >> Are >>>> you saying that it is repeating all of this sequence several times? >>>> If >> it >>>> is repeatedly rebooting itself at power up, there may be some >>>> hardware >>>> problem. It could be something simple, like the memory or rom sockets >> got >>>> dirty or a little corroded. Reseating the roms and the memory might >> clear >>>> it up. >>>> >>>>> Also when I press the parameter button in order to modify the > settings >> it >>>>> won't let me cycle through Timing, Keys, Midi and Loops. It usually >> gets >>>>> stuck bouncing between Timing and Keys (with each press of the >> Parameter >>>>> button) and will rarely cycle all the way through allowing me to get >> back >>> to >>>>> the "actual loop screen". I usually just half to shut it down and > power >>> back >>>>> up. I have tried resetting the EDP by holding down the Parameters >> button >>> but >>>>> that doesn't help. >>>>> >>>>> It's really strange all this started happening when I was trying to >> send >>>>> midi CC commands from my Behringer FCB1010 through my MOTU Midi >>> Timepiece >>>>> II to my Eclipse to change programs up and down. All of my midi gear > is >>>>> routed through my Timepiece but it has been setup like this for > almost >>> half >>>>> a year and no problems. Also my EDP is set to listen to notes and is > on >>> Midi >>>>> CH#4 and my Eclipse is on Midi CH#5. Are these errors I'm receiving >> just >>> a >>>>> coincidence or do they have a direct correlation to the CC >>>>> commands I >>> sent >>>>> to my Eclipse. Any ideas? >>>> >>>> If they are really on different channels it should be ok, but your >> problem >>>> smells a little like a midi loop to me. see if the EDP works when >>>> disconnected from the midi stuff and debug from there. >>>> >>>> kim >>>> >>>> >>>> >>>> ______________________________________________________________________ >>>> Kim Flint | Looper's Delight >>>> kflint@loopers-delight.com | http://www.loopers-delight.com >>>> >>>> >>> >>> >> >> >