Re: Oh no....more FCB1010 questions

["lol c" <testtubemicro@hotmail.com>]

Hi all

thanks so much for your help with the pedal.

I followed those instructions and it all went exactly to plan, now why 
cant 
berhinger set these damn things up properly them selves?

anyways

cheers again

Phill


>From: "Dave Sturt" <dave@davesturt.f9.co.uk>
>Reply-To: Loopers-Delight@loopers-delight.com
>To: <Loopers-Delight@loopers-delight.com>
>Subject: Re: Oh no....more FCB1010 questions
>Date: Wed, 25 Feb 2004 18:13:38 -0000
>
>Hi - sounds to me like you need to calibrate your pedals - I had the same
>problem.
>This info is from the very useful Yahoo FCB1010 user group.
>Hope it helps.
>
>Dave Sturt
>----------------------------------------------
>1. Keep footswitches 1 and 3 pressed while switching on the unit (This bit
>you can't
>
>do standing up!). Release the switches when the display blanks. The LEDs 
>on
>the
>
>footswitches, the ones on the display and each segment of the two numeric
>
>displays will turn on and off in sequence.
>
>2. Wait until all footswitch LEDs are on. Depress all footswitches one at 
>a
>time,
>
>including UP and DOWN, until all LEDs are off.
>
>3. Wait until relay switch test is finished. (There will be a couple of
>mechanical
>
>clicks, and the display will end up reading "F1" (at least, it did on
>mine)). [Also, if
>
>you have connected a MIDI cable between the MIDI in and out, the display
>will
>
>show "A1" before this, meaning the midi ports work correctly.]
>
>4. Press DOWN once.
>
>5. Adjust the left expression pedal (A) to the lowest value. Once adjusted
>press UP.
>
>6. Adjust the left expression pedal (A) to the highest value. Once 
>adjusted
>press UP.
>
>7. Adjust the right expression pedal (B) to the lowest value. Once 
>adjusted
>press UP.
>
>8. Adjust the right expression pedal (B) to the highest value. Once 
>adjusted
>press
>
>UP.
>
>9. Select a patch which has both pedals set to their full range, and check
>the
>
>expression pedals now send 0-127 (0x00-0x7F)
>
>----- Original Message -----
>From: "lol c" <testtubemicro@hotmail.com>
>To: <Loopers-Delight@loopers-delight.com>
>Sent: Wednesday, February 25, 2004 3:32 PM
>Subject: Oh no....more FCB1010 questions
>
>
> > Hi all
> >
> > I know how often this stuff comes up on list and belive me i have tried
>for
> > the last week to NOT post to list for help. but Ive reached the stage
>where
> > I cant complete my tailor made midi board just becaus of one problem...
> >
> > Basically I cant get the controller pedals to respond.
> >
> > Im using Loop4 and Midi FCB1010.
> >
> > Ive got the "patches" set up so that I have record,overdub,
>multiply,insert,
> > replace, undo, speed, drection, substitute, and next in that order on
>patch
> > bay one, then the same but in suspend mode on page two, then a few 
>presets
> > stored in page three......ok so far so good.
> >
> > now on each of these presets I have the buttons of each controller lit 
>and
> > active and set to 7 for feedback and 1 for Volume.
> >
> > on the echoplex I have  the buttons in the perameters corrispondinf to
> > feedback and volume set to 7 and one respectivly, yet.........nothing.
> >
> > I can move the continuos controller pedals back and forth and the 
>reout 
>on
> > the screen never changes to display a new feedback or volume setting
> >
> > whats going on?
> >
> > Help me please
> >
> > Phill Wilson
> >
> > _________________________________________________________________
> > Express yourself with cool new emoticons
>http://www.msn.co.uk/specials/myemo
> >
>

_________________________________________________________________
Express yourself with cool new emoticons 
http://www.msn.co.uk/specials/myemo