Support
Looper's Delight
|
Support |
|
|
This is late but anyway; thanks Per and to Kris for the EDP stereo sync parameters!! Great. Been busy but I`ll soon check my EDP settings to see how they correspond. T. ----- Original Message ----- From: "Hartung, Kris" <kris.hartung@hp.com> To: <Loopers-Delight@loopers-delight.com> Sent: Sunday, July 10, 2005 8:40 PM Subject: RE: Troubleshooting my EDPs and FCB....Again (factory reset guidance) Torstein - Before I get to working on my FCB, I'll post the parameters that fixed my drift problems several months ago...haven't had any problems since then....I use the TSR cable connect the two units via Brother Sync, plus run MIDI out from one to the MIDI in of the other. Kris Parameter settings for both units, horizontal across the unit, left to right: Loops MoreLoops=2L AutoRecord=ON LoopCopy=OFF SwitchQuant=LOP LoopTrig#=84 Velocity=OFF SamplerStyle=RUN MIDI Channel=1 ControlSource=Ctr (FIRST CRITICAL SETTING, AS STATED IN MANUAL...could be "not" as well) Source#=36 VolumeCont=7 FeedBkCont=1 Dump=001 h Load=001 - Switches RecordMode=tOG OverdubMode=tOG RoundMode=OFF InsertMode=rEV MuteMode=StA Overflow=PLY Presets=Pr.E Timing Loop/Delay=LOP Quantize=OFF 8ths/Cycle=1 Sync=OUT (SECOND CRITICAL SETTING, AS STATED IN MANUAL) Threshold=0 (THIRD CRITICAL SETTING, NOT IN MANUAL...NEEDS TO BE SET TO 0) Reverse=[Shows No Setting] StartPoint=[Shows No Setting, but "1" at the first LED] -----Original Message----- From: Torstein H. Rem [mailto:thelgere@online.no] Sent: Sunday, July 10, 2005 12:24 PM To: Loopers-Delight@loopers-delight.com Subject: Re: Troubleshooting my EDPs and FCB....Again (factory reset guidance) To Kris an others with two EDP`s. While talking about syncing two EDP`s I``ll use the chance to ask about sync problems. Even when hooked up right I have problems. For each repeat of a loop the soundstage will drift over to one side more and more and getting out of phase. Next time (loop) it might drift over to the other side. More or less randomly. This has been discussed before, I believe. Someone installed some new clock(s) ? What to do about it? Both my EDP`s are from the same period (beige Gibson). Thanks! T. ----- Original Message ----- From: "Hartung, Kris" <kris.hartung@hp.com> To: <Loopers-Delight@loopers-delight.com> Sent: Sunday, July 10, 2005 7:39 PM Subject: RE: Troubleshooting my EDPs and FCB....Again (factory reset guidance) I'll give it a try. I was wondering, since my problem only occurs with both units, what about using my MIDI splitter to go from the FCB to the EDPs, rather than to one EDP and then MIDI out of that one to the next? I would still use the Brother Sync of course. Kris -----Original Message----- From: Per Boysen [mailto:per@boysen.se] Sent: Sunday, July 10, 2005 4:09 AM To: Loopers-Delight@loopers-delight.com Subject: Re: Troubleshooting my EDPs and FCB....Again (factory reset guidance) On Jul 10, 2005, at 11:57, Hartung, Kris wrote: > Before I start troubleshooting in detail, I thought I would try > resetting the FCB to factory state first. However, I am confused by > what the manual says about this. It shows three ways to perform a > factory > reset: V-AMP family products, BEHRINGER guitar amps, and BASS V-AMP > product range. Is there a particular reset option I should choose? No. Whatever reset you use you will have to empty the banks and put in new data for the EDP. When programming your FCB banks you must be aware of that the FCB can send multiple midi commands on every button press. In the FCB patch programming mode you have to disable everything except for what the EDP needs. Otherwise you will go nuts when trying to get it right ;-) Greetings from Sweden Per Boysen www.looproom.com (international) www.boysen.se (Swedish) ---> iTunes Music Store (digital) www.cdbaby.com/perboysen