Support
Looper's Delight
|
Support |
|
|
I'll add that in tonight or tomorrow.... TravisH On 10/30/05, Kris Hartung <khartung@cableone.net> wrote: > Cool. Thanks, Travis. I think I ended up changing the EDP MIDI Source # >to 0 > so that I could use the MIDI notes same as pedal #'s. > > Now what would be ideal are steps to make exp. pedals A and B control > feedback and volume...I did already but forgot how I did it! > > k- > ----- Original Message ----- > From: "Travis Hartnett" <travishartnett@gmail.com> > To: <Loopers-Delight@loopers-delight.com> > Sent: Sunday, October 30, 2005 2:40 PM > Subject: Programming the Behringer FCB1010 for Echoplex use, a quick >guide > > > I just spent a few hours with the Behringer trying to program it to > work with my EDP. I found the FCB manual to be confusing, and a quick > search of the archives here didn't turn up what I was looking for, so > for the aid of anyone else trying to program the damn thing by hand, > here's a very brief, very quick guide. If there's interest, I'll > update this with suggestions or corrections. > > TravisH > > **************** > > 1. Turn on the Behringer FCB1010 and the Echoplex. Connect the MIDI > out jack to the MIDI In jack on the Echoplex. Make sure the EDP MIDI > Control Source parameter is set to "not" (for "note") and that both > devices are set to the same MIDI channel. > > 2. Select the bank and patch you wish to edit with the UP and DOWN >buttons. > > 3. Enter Edit mode by pressing the DOWN button for 3 seconds, or until > the two-digit bank indicator goes off and the first green LED under > Preset Configuration starts blinking. > > 4. Press the UP/Enter button. > > 5. Some the program button LEDs may now be lit, depending on what's > already been stored in the patch either at the factory or by you or > whoever you bought the FCB from. You want to clear all that out so > that you're not sending a bunch of unwanted MIDI data. Often, the 1, > 8 and 9 buttons will be "on" in a factory preset. You want to turn > those off, so hold down each button until the LED turns off. This > takes about two seconds. > > 6. Once all the program button LEDs are off, hold down the 0 button > until its LED comes on. This indicates that you're going to be > editing the MIDI note which is going to be sent by this patch. > > 7. Press the 0 button again. Its LED should now be blinking. > > 8. Press the UP/Enter button. The Select LED should turn off, the > Number LED should turn on and the two-digit display should now be on > and displaying "00" with the second "0" flashing. > > 9. Now you can enter the MIDI note number that you want transmitted. > For example, the Record function is triggered by a note number of 38. > Use the program buttons (the 0-9 buttons) to enter the note value. > > 10. When you've got the desired note value showing on the three-digit > display, press the UP/Enter button. The three-digit display will turn > off, the 0 button LED will go to steady on, the Number LED will go > off, and the Select LED will go steady on. > > 11. If you're finished editing that patch, hold down the DOWN button > for three seconds or until three-digit display comes back on > displaying the current bank. At that point, you're in the "ready to > use" mode, and if you press the patch button you've just edited you > should see the EDP respond in the desired manner. > > The note values for the EFC-7 button equivalents are as follows: > > 38 RecordButton > 39 OverdubButton > 40 MultiplyButton > 41 InsertButton > 42 MuteButton > 43 UndoButton > 44 NextButton > > For a more complete list of all the available MIDI commands, refer to > the manual or the spreadsheet here: > http://www.loopers-delight.com/tools/echoplex/PLEX_MIDI_COMMANDS.zip > > > >