Support
Looper's Delight
|
Support |
|
|
> Then I opened the Midi Sync preferences. At the top there are five > or so slots with control surface, input and output with BCR 2000 > in each of them on one row. I'm not exactly sure what these do, but you should click on any item that shows BCR 2000 and select "None". This may be diverting some of the MIDI messages sent by the BCR for Live control. > I ignored those for the most and went to the lower half of that > screen where it had midi ports track, sync and remote with the BCR as > an option then my audio interface sync port and output with the BCR. > Following Jeff's advice, I made sure ONLY sync was on for the BCR > input. However, when I did this, Live dids not recognize the incoming > FCB via BCR signal. If I turn on the Remote box as well, Live can > read the FCB/BCR. No, the Track button needs to be On and the Sync and Remote buttons need to be Off. I think Sync determines if Live will follow MIDI clocks from this device which does not apply here. Remote determines if Live will use the MIDI messages for its own purposes which we don't want. You only need Track. > One last thing, I programmed ther FCB to be sending ONLY note > messages, nothing else was selected and yet every second press of the > note button (so two pair of on/off messages) it was throwing a control > message that had a label that seemed to change from session to > session. Once it was mute all sound 15 (or other numbers). Earlier I > was registering it as a portamento control. The BCR isn't registering > any of its own button presses or dial turns in the Monitor so these > only come when the FCB is pressed. I'm not sure what that is, but as long as you don't program Mobius to respond to the extra CC it should be okay. Jeff On Apr 14, 2012, at 12:47 AM, Kevin Cheli-Colando wrote: > Okay, so this is getting farther and farther afield from my having any > clue what is going on with my arrangement of Mobius. > > So, tonight I decided to go back to zero and start forward with the > advice I've gotten, most notably Jeff's walk through with the nanokey. > I booted up, checked my midi stream with Midi Monitor and confirmed > the FCB is sending Note on and off signals (I had programmed a new > bank in the FCB with ONLY Note selected). > > Oh yes, I don't have a direct midi port connection with this > arrangement. I am running the FCB Midi cable into a Behringer BCR2000 > rotary controller which connects via USB. I have the BCR set to send > incoming midi through. Strangely enough however, the Monitor only see > data from the FCB, the BCR doesn't seem to be getting anything to the > computer. > > So anyway, I started fresh in Live, created one audio track, one midi > track, dropped Mobius in the audio and directed the midi to the audio > and selected input from BCR 2000 on the midi channel. Then I opened > the Midi Sync preferences. At the top there are five or so slots with > control surface, input and output with BCR 2000 in each of them on one > row. I ignored those for the most and went to the lower half of that > screen where it had midi ports track, sync and remote with the BCR as > an option then my audio interface sync port and output with the BCR. > Following Jeff's advice, I made sure ONLY sync was on for the BCR > input. However, when I did this, Live dids not recognize the incoming > FCB via BCR signal. If I turn on the Remote box as well, Live can > read the FCB/BCR. > > So, no Remote, no communication. > > Went out of live and confirmed that I can program the pedal directly > to mobius and it runs fine. > > Came back to live and cleared the part of the Midi preferences with > the controller surface in and out, moved all of them to none. Tried > to program Mobius in live again and this time was able to record(!) > but when I pressed record again, the loop stopped and disappeared. > > Is it possible to run Mobius outside of live and route it to the input > of an audio track (or two). > > I don't know, I'm stumped. It requires that the remote box is checked > with Jeff says that should be off, but when it is of, I get no midi > signal. And do I need to worry about the control surface or midi > output. > > One last thing, I programmed ther FCB to be sending ONLY note > messages, nothing else was selected and yet every second press of the > note button (so two pair of on/off messages) it was throwing a control > message that had a label that seemed to change from session to > session. Once it was mute all sound 15 (or other numbers). Earlier I > was registering it as a portamento control. The BCR isn't registering > any of its own button presses or dial turns in the Monitor so these > only come when the FCB is pressed. > > As I said before, stumped. > > Kevin > > -- > Till now you seriously considered yourself to be the body and to have a > form. That is the primal ignorance which is the root cause of all > trouble. > > - Ramana Maharshi (1879-1950) > > Sound and Vision: http://www.minds-eye.org > Video http://www.vimeo.com/user877640/videos >