Re: Repeater start/stop messages

["Michael LaMeyer" <m.lameyer@verizon.net>]

sorry cliff, hope you don't mind if i post this to the list, i
gotta subscribe with an account that i can properly set replies
for ...

mike

----- Original Message -----
From: "Clifford Novey" <om@om-studios.com>
To: "Michael LaMeyer" <m.lameyer@verizon.net>
Sent: Monday, April 15, 2002 2:01 PM
Subject: Re: Repeater start/stop messages


> Hehe- YES! That helps- and of course it was in the manual- I'm
smart.
> Thanks!!
>
> Cliff
>
> ----- Original Message -----
> From: "Michael LaMeyer" <m.lameyer@verizon.net>
> To: <Loopers-Delight@loopers-delight.com>
> Sent: Monday, April 15, 2002 10:55 AM
> Subject: Re: Repeater start/stop messages
>
>
> > would this apply?
> >
> > (from the most recent repeater manual):
> >
> > Advanced MIDI RT tweaking
> > In some situations it may be desirable for Repeater to NOT
send
> > out MIDI RT start, stop and SPP messages. The output of
these
> > messages can be inhibited/enabled by sending Repeater the
> > Inhibit MIDI RT Control CC message.
> >
> > The Inhibit MIDI RT Control CC message is:
> >
> > CC:    112
> > value:  0-63 (off) 64-127 (on)
> >
> > mike
> >
> > ----- Original Message -----
> > From: "Clifford Novey" <om@om-studios.com>
> > To: <Loopers-Delight@loopers-delight.com>
> > Sent: Monday, April 15, 2002 1:37 PM
> > Subject: Re: Repeater start/stop messages
> >
> >
> > > No because the start/stop messages are just like midi
clock-
> > it doese,nt
> > > matter what chanel you are on because the info is
broadcast on
> > all channels
> > > regardless of selection.
> > >
> > > c
> > >
> > > ----- Original Message -----
> > > From: "jim palmer" <jimp@pobox.com>
> > > To: <Loopers-Delight@loopers-delight.com>
> > > Sent: Monday, April 15, 2002 7:34 AM
> > > Subject: Re: Repeater start/stop messages
> > >
> > >
> > > > i may be misunderstanding your problem, but can't you
solve
> > > > this by setting his repeater to a different channel than
> > your repeater?
> > > >
> > > > >... the issue is that I am using everything on
> > > > > a Thru chain and his Repeater start/stop is being
> > controlled by mine
> > > > > which we do NOT want- and I do not want to use the
midi
> > Out of any of
> > > > > the other devices either. We just need the clock to
lock
> > to- the
> > > > > start/stop messages are part of the clock stream which
> > does not pay
> > > > > attention to midi channel- How can we filter this data
out
> > without using
> > > > > a computer? I looked at the MidiSoloutions mapper and
> > installed the
> > > > > software for it but it only maps/converts messages
other
> > than real-time
> > > > > clock etc. Any info appreciated.
> > > > >
> > > > > Cliff
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>
>